Newport Coast Solar Quotes

So, what exactly is involved in calculating solar panels cost in Newport Coast? When thinking about solar power very few people know the way the cost of solar panel systems is actually measured. Or even, for that matter, do we automatically grasp the connection relating to the cost of solar power and the value of solar power. We all know that gasoline prices are in dollars per gallon. We likewise are all aware of approximately how far we’ll be able to drive after spending 40 bucks for a tank of gas. In contrast to a tank of gas, the value of which can be consumed pretty much instantly, solar panels deliver their value across a period of time.

How Much Does It Cost To Install A Solar Panel

Newport Coast 3 Undervalued Solar Leaders

A home with solar panels installed on its roof that supply power to the water heater will be more energy efficient than a standard home. Solar panels can save you 50 to 75 percent on your monthly electric bill. Over time, you may need to remove and replace solar panels from the roof of your home. Also, you might choose to remove the panels completely. The removal process is relatively straightforward, but certain steps must be followed. Things You'll Need Toolbox Replacement panels Ladder Gloves Place a ladder against the side of your house in order to gain access to the roof. Put on a pair of sturdy gloves before touching or handling any of the solar panels. Some solar panels have contents that are not safe for long-term exposure, so use caution during the removal process. Determine which panels are damaged or not working. Solar panels have a life expectancy of 25 years, so check with the company that manufactured the panels to determine if they are under warranty. Purchase replacement panels, if necessary. Turn off the pump that is connected to the solar water heater panels. Allow time for the pipes to drain adequately before removing any panels. Deactivate the pump so that it does not dry out and become damaged while the solar panels are being removed or replaced. Determine what tools will be necessary in order to remove some or all of the solar panels. A variety of mounting equipment could have been used, including screws, brackets or wing nuts. Save the mounting equipment if new panels are going to be installed. Disconnect the pipes at either end of the solar panel. Drain any excess water out of the pipes and panel before removing the panel from the roof. Continue the removal process until all of the panels are removed or the damaged ones are replaced. Connect any new panels and turn the water pump back on. The new panels will not work to full capacity for 24 hours. Check with your local environmental agency or the EPA to determine how to dispose of the solar panels correctly. Related Searches References Energy Savers: Solar Panel Maintenance and Repair Earth 911: Solar Panel Disposal Promoted By Zergnet Comments Please enable JavaScript to view the comments powered by Disqus. You May Also Like Life Expectancy of Solar Panels With care and cleaning, solar panels can last up to 40 years. Certain issues can make them fail, but in general a... How to Clean Mold Off a Roof Mold or mildew makes black ugly streaks on a roof. Not only is it unattractive, it can actually shorten the life of... How to Maintain a Solar Panel Whether a solar panel system is designed to generate heat for our homes or produce electricity, a properly functioning solar panel is... How to Add Solar Panels to a Flat Roof With growing concerns over the environmental effects of burning fossil fuels and rising energy prices, many people are looking to renewable energy... How to Install Solar Panels on a Tile Roof Solar panels can be installed on many roof types. The panels can be tilted up as well as flush-mounted. It is much... How to Build Solar Hot Water Panels If you have a few carpentry tools, you can build a solar hot water heater with materials you probably already have around... How to Convert an Old Water Heater to a Solar Water Heater Billions of photons stream from the Sun to the Earth. When photons strike the Earth's surface atoms begin moving faster. The increased... Solar Panel Installation Cost

Best Science Fair Project Websites for Kids

Caption: Kokam 24-megawatt Energy Storage System (NYSE:ESS), used by South Korea's largest utility, Korea Electric Power Corporation (KEPCO): world's largest Lithium NMC ESS for frequency regulation

Sometimes technology creeps up on you before you realize what is happening. Then something happens to get your attention and you realize that things are changing fast. And so it is with batteries, the missing link in replacing fossil fuels with renewable energy.

Here I cover two areas of battery technology that are transforming power management at scale. The first comes out of left field as a solution to frequency regulation in power plants. The second relates to management of excess energy generated by solar and wind, followed by dispatch of that energy when needed. At its most extreme this role may involve near complete charge and discharge once, or even twice, in a single day, every day.

Grid reliability, increased efficiency and frequency regulation

Late last month Kokam (XKRX:040480) a veteran Lithium ion South Korean battery manufacturer, announced the deployment of 3 high performance Lithium ion battery systems to provide 56MW of specialized batteries for frequency regulation in large power plants in South Korea. The batteries are: two Kokam Lithium Nickel Manganese Cobalt (NMC) battery systems with capacities of 24 MW/9 MWh and 16MW/6MWh, and a 16MW/5MWh Lithium Titanate Oxide (LTO) battery system. The LTO system was implemented first. While LTO technology is robust, with less dependence on temperature control, it is more expensive than NMC batteries and the specifications from the utilities often require temperature control (hence housing in containers which are cooled or heated). I suspect that NMC will become the preferred technology for frequency regulation.

The 24MW NMC battery system is the largest used in the world for frequency regulation. These batteries provide the Korea Electric Power Corporation (KEPCO) (NYSE:KEP) with ~10% of the frequency regulation needed to allow its entire system to run largely with batteries. KEPCO plans to install ~500MW of rapid response batteries by 2017 to effectively wean South Korea off the need for fossil fuel to provide this reserve power need for frequency regulation. Several battery manufacturers are involved in this project (Kokam, LG Chem (OTC:LGCLF), Samsung (OTC:SSNLF). It isn't clear how much KEPCO has already installed but it may be as much as 230MW of batteries for frequency regulation.

South Korea is special in that it has a single power authority, KEPCO, which is largely responsible for managing the nation's power capacity. So it is possible for one organization to setup a national program to manage 65 GW of power capacity. This capacity is mostly coal powered (~47GW) but with substantial nuclear and hydro capacity (~18GW). There is a very small contribution of wind and solar renewable energy in South Korea.

Currently ~5% of the coal needed to run a coal fired plant is dedicated to frequency regulation, so having batteries take over this role is a substantial saving in coal used. More importantly the South Korean plans (within 2 years!) indicate one of the first examples of batteries assuming a central role in an aspect of power generation that has been seen as a fossil fuel role.

Clearly Kokam doesn't see South Korea as the only market for this role and they have pilot facilities (2-5MW) being reviewed in both Germany and the US. Kokam has the capacity to deliver 100's of MW of the NMC frequency regulation batteries at short notice.

There is a lot of interest in fast response Lithium batteries and a substantial system (2MW) was recently announced in the UK using Toshiba (OTCPK:TOSYY) Lithium Titanate batteries in association with energy company E.ON (OTCPK:E.ON) and it's wholly owned subsidiary Uniper at the Willenhall substation. E.ON also has a 10MW/2.5MWh battery system under development with Tucson Electric Power in Arizona. E.ON is shortlisted for a 250MW tender for frequency response storage in the UK and Kokam is involved in tendering, so Korea's implementation is being watched in Europe too.

Interestingly lithium technology is being used to replace lead acid batteries by Duke Energy (NYSE:DUK) in a 35MW facility. There are also major frequency regulation projects in Canada (e.g. 12MW system in Ontario's Independent Electrical System Operator).

These Lithium NMC and LTO batteries are also useful for peak load management improving power quality and reliability in solar and wind applications, and also for spinning reserve applications.

Energy management for renewable energy

This is a big one, as you need a way to store and then access the intermittent power from solar PV and wind. Unlike the frequency regulation application described above, which needs fast, but short term response and high power delivery, energy arbitrage for solar and wind smoothing requires slower and longer term charge/discharge (up to over a number of hours).

A frequency regulation application has a high life cycle (10,000, compared with 4000-8000 with arbitrage), high power (i.e higher than arbitrage), but lower energy density than arbitrage. Because frequency regulation is a special rapid application it is more costly than an arbitrage battery.

The actual needs for energy management at scale are more varied than frequency regulation and so the actual configurations for batteries for this purpose are still evolving. It might be that the critical requirement is ramp rate control, or charge/discharge over hours may be more critical. Battery manufacturers are focusing in on their preferred configurations. For example Kokam has a High Energy NMC battery for energy management at scale.

For the technically minded here are a couple of links to give a sense of the kinds of lithium battery technology and how the different formulations behave. A good summary is here, and for those who want a deeper dive into lithium battery chemistry, here is a pretty up to date article.

Energy management applications for renewable power generation

Pumped hydro

Pumped hydro has a significant role in energy storage and this is well established with 140GW of pumped hydro already implemented. This large scale storage allows long term (even seasonal) energy storage.

There are surely many old mines, with tailing dams at the top and down below an open cut mine, that can be flooded. GW levels of power can be addressed in such schemes, but the capital costs are not small and they attract controversy because of their size. Two pumped hydro projects in California, Eagle Mountain and Iowa Hill, have been on this path for a long time, but capital and approvals are elusive.

Lithium batteries

This is happening at several levels. The easy one involves home solar PV systems linking with a home battery. Because it is a small cost (relatively) and the market is big (1.5 million homes in Australia have solar PV), just about all of the battery providers are interested. Here numbers matter as many small systems add up to a lot of power managed and it is managed locally (at the individual house level).

The harder thing is larger scale energy management, and detractors of Lithium batteries point to frequency regulation to indicate why Lithium batteries are inappropriate for energy arbitrage. However, Lithium battery chemistry configured for frequency regulation is not the only chemistry or configuration for lithium batteries, as Tesla is doing fine with its electric cars that have a range of several hundred miles and hence can discharge over many hours.

It seems that a 40ft container housing a 2-2.5MWh system is the scale for a number of utility energy management systems, but systems as large as 100MWh give a sense of the scale being implemented. Obviously a 100MWh plant would involve 40 x 2.5MWh 40ft containers.

Utilities adopting lithium battery energy management applications

There are now many multiple MW systems being installed for this kind of application. Kokam gives details of 12 of its systems installed in the US, South Korea and Australia that have more than 1MW power capacity. In 2015 Kokam alone installed 85MW of battery storage systems and 75MW of that capacity was larger than 1MW.

Substantial lithium batteries are also being adopted (along with solar PV) in remote and mining communities to partially substitute for diesel-powered systems. For example a remote indigenous community in Northern Australia is installing a 2MWh lithium battery storage system to store solar PV and take over grid forming functions from a diesel system. This will allow switchoff of the diesel system during the day as well as storing solar PV produced power.

Lithium batteries as part of a renewable energy project

Clearly renewable energy projects are considering including arbitrage, as there are various management functions that batteries do well, and holding the power generated to be delivered at a time when the value of the energy is greater may make sense. An early example of this kind of arbitrage involves Statoil (NYSE:STO) which recently announced a pilot 1MWh Lithium battery (technology not given) storage system to complement its Hywind Scottish floating 30MW wind farm.

Image : Statoil Hywind turbine

However, there are other battery technologies for deep charge/discharge on a daily basis. While at an earlier stage of development, flow batteries seem well suited to this task. It is a race to see if flow batteries will get a place at the table or whether lithium batteries now have sufficient momentum to dominate the battery arbitrage space.

Update on flow batteries

Six months ago I wrote an article on three flow battery companies (Redflow (ASX:RFX), Imergy Power Systems and ViZn Energy which had partnered with substantial manufacturing companies (Flextronics (NASDAQ:FLEX), Foxconn (OTC:FXCOF) (TWSE:2354) and JBL Circuit (NYSE:JBL) respectively for manufacture of their flow batteries.

While it is too soon to see a lot of progress, there have been developments in each of the partnerships.

Redflow/Flextronics ZnBr flow batteries :

The last 6 months have seen substantial progress with Flextronics now assuming 100% of manufacturing from Redflow. Flextronics now controls all aspects of manufacturing of the RedFlow batteries, with production ramp up in April 2016.

In 2015 in partnership with FLEX, manufacturing costs have been decreased by 15%, the lifecycle/longevity has been improved and cycle cost/kWh over battery lifetime decreased by 50%. Redflow will soon deliver an on-grid demonstration 0.1MW/0.48MWh flow battery system to Ergon Energy.

In addition to exploring remote markets around the world, Redflow is entering the Australian home battery market with a smaller offering. The Redflow share price has doubled since the start of 2016.

Imergy Power Systems/Foxconn :

It is too early to know how the Imergy projects in India, China and Africa are proceeding, although the status of the Sun Edison (NYSE:SUNE) purchase of up to 1000 of Imergy's vanadium flow batteries for implementing in India could be problematic given the disaster that has recently befallen SUNE and news that it is not supporting its activities in India. The rumor is that Adani (IN:ADANIT) may be interested in SUNE's Indian projects.

Recently (end of February 2016) SUNE announced agreement with Ontario Independent Electricity System Operator (Ontario IESO) to supply an Imergy 5MW/20MWh system in 2017; this was to be SUNE's first large scale grid-connected energy storage project and it will need to be restructured with SUNE in difficulty. Imergy and Foxconn will need to think creatively about diversifying the route to market for their flow batteries.

ViZn Energy/JBL Circuit : ViZn reported 20% improved capacity and reduced life cycle degradation, which is important for frequency regulation applications.

At the end of the day there will be winners and losers and here sits the dilemma for investors. Is it still too soon to know which technology to back and which companies to invest in? Given the intense interest in frequency regulation I suspect that this market, will be satisfied soon by companies like Kokam and LG Chem who have done the hard yards on understanding Lithium battery chemistry. I suspect that for management of renewable energy it will end up a combination of pumped hydro, Lithium and flow battery technologies, with the latter becoming increasingly important.

What is abundantly clear is that all investors need to look carefully at their fossil fuel portfolios, as the complacency that the switch to renewable energy (with storage) is going to take a long time seems misguided in 2016.

Conclusion

This story about battery storage starting to do heavy lifting has implications in two areas of large scale energy supply: frequency regulation and management of renewable energy. It will help resolve issues of intermittency of renewable energy. The impact will be felt not only on adoption of renewable energy (and hence solar and wind companies) but also on fossil fuel power generation. Investors in fossil fuels should think carefully about where this is heading.

Disclosure: I am/we are long ASX:RFX.

I wrote this article myself, and it expresses my own opinions. I am not receiving compensation for it (other than from Seeking Alpha). I have no business relationship with any company whose stock is mentioned in this article.

Editor's Note: This article covers one or more stocks trading at less than $1 per share and/or with less than a $100 million market cap. Please be aware of the risks associated with these stocks.

Newport Coast

Ways to Save Mother Earth


Solar Panels San Diego